Skip to main content
  1. Welcome to the tutorial how to upgrade your Original Prusa i3 MK2/S to Original Prusa i3 MK2.5S
    • Welcome to the tutorial how to upgrade your Original Prusa i3 MK2/S to Original Prusa i3 MK2.5S

    • Please prepare MK2.5S upgrade kit received from Prusa Research.

    • The items on the picture might differ from yours.

    • WARNING: This assembly guide is valid ONLY FOR SINGLE MATERIAL MK2.5S!!! For MK2.5S MMU2S, please wait for the guide to be published. Different parts are needed!

  2. For the MK2.5S upgrade you will need:
    • For the MK2.5S upgrade you will need:

    • Needle-nose pliers (1x)

    • Allen key 2.5 mm

    • Allen key 2.0 mm

    • Allen key 1.5 mm

    • Slotted screwdriver for the belt insertion

    • No soldering is required.

    • No wire crimping is required.

  3. Most of the labels are scaled 1:1 and can be used to identify the part :-) For the most common screws, nuts and PTFE tubes. You can also use the enclosed letter, which contains Prusa Cheatsheet on the other side.
    • Most of the labels are scaled 1:1 and can be used to identify the part :-)

    • For the most common screws, nuts and PTFE tubes. You can also use the enclosed letter, which contains Prusa Cheatsheet on the other side.

    • You can download Prusa Cheatsheet from our site. Print it at 100 %, don't rescale it, otherwise it won't work.

  4. manual.prusa3d.com で組み立てガイドをご覧の場合には、高画質なオリジナルの画像をご利用いただけます。
    • manual.prusa3d.com で組み立てガイドをご覧の場合には、高画質なオリジナルの画像をご利用いただけます。

    • カーソルを画像の上に移動し、左上に表示されている拡大鏡のアイコン ("View original") をクリックします。

  5. Most of the 3D printed parts on  Original Prusa i3 MK2.5S most are marked with their version.
    • Most of the 3D printed parts on Original Prusa i3 MK2.5S most are marked with their version.

    • Cx series (e.g. C1) - those parts are printed on Prusa Research farm and are distributed with the kit.

    • Rx series (e.g. R4) - those parts are available for download and printing by the user. They are identical to the factory ones.

    • In case you have issues while assembling the printer with the certain printed part, please try to find this label and tell it to our support team.

  6. Before we start disassembly, you need to print all the necessary parts. If you already have the parts, you can skip to the next step. For MK2/S to MK2.5S upgrade you need to print the extruder parts, which are separated into more G-codes. Use enclosed BLACK PETG or similar material. The colour should be black to avoid issues.
    • Before we start disassembly, you need to print all the necessary parts. If you already have the parts, you can skip to the next step.

    • For MK2/S to MK2.5S upgrade you need to print the extruder parts, which are separated into more G-codes. Use enclosed BLACK PETG or similar material. The colour should be black to avoid issues.

    • G-codes and STL files are available on our website: prusa3d.com/prusa-i3-printable-parts

    • For printing individual parts it is recommended to use Slic3r PE with 0.2 mm layer height, GRID infill at 20%, no supports!

    • Fan-shroud must be printed from ABS only!!! We include this part in the upgrade package.

    • The pictures does not represent all the parts.

  7. マニュアルで不明な点がありましたか? ネジが紛失していたり、プリント部品にクラックが入ってしまっていたりしましたか? 是非教えてください! 以下の方法よりご連絡いただけます。
    • マニュアルで不明な点がありましたか? ネジが紛失していたり、プリント部品にクラックが入ってしまっていたりしましたか? 是非教えてください!

    • 以下の方法よりご連絡いただけます。

    • それぞれのステップの下部からコメントする。

    • shop.prusa3d.com のライブチャットを使う。

    • メールを japan@prusa3d.com へ送る。

  8. 3D printed parts are very precise, however, there still might be a tolerance in the printed part and same goes for the size of the nut. Therefore it might happen, that the nut won't fit easily in or might be falling out. Let's see, how to fix it: Nut won't fit in: use a screw with a thread along its entire length (typically: M3x10, M3x18) and screw it from the opposite side of the opening. While tightening the screw, the nut will be pulled in. Remove the screw afterwards.
    • 3D printed parts are very precise, however, there still might be a tolerance in the printed part and same goes for the size of the nut.

    • Therefore it might happen, that the nut won't fit easily in or might be falling out. Let's see, how to fix it:

    • Nut won't fit in: use a screw with a thread along its entire length (typically: M3x10, M3x18) and screw it from the opposite side of the opening. While tightening the screw, the nut will be pulled in. Remove the screw afterwards.

    • Nut keeps falling out: Use a piece of tape to fix the nut temporarily in place, as soon as you insert the screw in, you can remove the tape. Using glue isn't recommended as it can partly reach into the thread and you won't be able to tighten the screw properly.

    • Every time we recommend to use the "screw pulling technique", you will be reminded with Joe's avatar ;)

    • Parts in the pictures are used as an example.

  9. To successfully finish the assembly please follow all these: Always read all the instructions at current step first, it will help you to understand, what you need to do.
    • To successfully finish the assembly please follow all these:

    • Always read all the instructions at current step first, it will help you to understand, what you need to do.

    • Don't follow pictures only! It is not enough, the written instructions are as brief as they could be. Read them.

    • Read the comments from the other users, they are great source of ideas. We read them too and based on your feedback improve the manual and the entire assembly.

    • Use a reasonable force, the printed parts are tough, but not unbreakable. If it doesn't fit, check your approach twice.

    • Most important: Enjoy the build, have fun. Cooperate with your kids, friends or wives. However, we take no responsibility for possible fights ;)

    • READY? You can start by assembling Y-axis in the next chapter - 2. 分解

Finish Line

Dozuki System

Member since: 09/24/2009

726 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 8

All Time: 15